SeeedStudio Grove There are 25 products.

per page
Showing 1 - 16 of 25 items
  • € 5,00 In Stock

    Starter bundle harness is a board holding the goods of grove-starter bundle ,include the LCD and battery box,arduino,seeedunio and ect.

    € 5,00
    In Stock
  • € 16,00 In Stock

    Based on the excellent ADXL-345, this digital 3-axis accelerometer has excellent EMI protection. Its variable output makes it suitable for a wide range of applications

    € 16,00
    In Stock
  • € 8,50 In Stock

    This temperature & humidity sensor provides a pre-calibrated digital output. A unique capacitive sensor element measures relative humidity and the temperature is measured by a negative temperature coefficient (NTC) thermistor. It has excellent reliability and long term stability. Please note that this sensor will not work for temperatures below 0 degree. 

    € 8,50
    In Stock
  • € 3,50 In Stock

    The Light sensor module uses the GL5528 photoresistor to detect the light intensity of the environment. The resistance of the sensor decreases when the light intensity of the environment increases. The chip LM358 is used as a voltage follower to enable you get a accurate data.

    € 3,50
    In Stock
  • € 7,00 In Stock

    his slide potentiometer is a linear variable resistor with a total resistance of 10k. When you move the lever from one side to the other, its output voltage will range between 0 V to the VCC you apply. 

    € 7,00
    In Stock
  • € 4,50 In Stock

    Chainable RGB LED Twig is based on P9813 chip which is a full-color light source LED driver chip,can provide constant current drive and modulated output of 256 gray.Transmission by wire (DATA and CLK), built-in recycling, can enhance the transmission distance.

    € 4,50
    In Stock
  • € 2,25 In Stock

    This new version of LED twig consists of one green LED. It operates from 5V DC. Perfect for use on Seeeduino digital outputs, or also can be controlled using pulse-width modulation. Each LED has a current-limiting resistor, which protects the LED and the Arduino from high current.

    € 2,25
    In Stock
  • € 3,50 In Stock

    Grove - Screw Terminal with four 3.5mm pitch pins rate up to 125V @ 6A. Terminal can accept 30 to 20AWG wire. It is most common pitch screw terminal. This grove has four ports, include GND, VCC and two other undefined ports. 

    € 3,50
    In Stock
  • € 4,00 In Stock

    This is a simple yet enjoyable twig to use. The piezo can be connected to digital outputs, and will emit a tone when the output is high. Alternatively it can be connected to an analog pulse-width modulation output to generate various tones and effects.

    € 4,00
    In Stock
  • € 2,50 In Stock

    This new version of button twig contains one independent button, which are configured with pull-down resistor ? Ready for use with our microcontrollers as digital input. The button signals the SIG wire,NC is not used on this twig.

    € 2,50
    In Stock
  • € 2,50 In Stock

    The tilt-switch twig is the equivalent of a button, and is used as a digital input. When the switch is level it is open, and when tilted, the switch closes. It is wired to the SIG line, NC is not used on this twig. There's a surface-mount resistor .

    € 2,50
    In Stock
  • € 7,00 In Stock

    Grove - Thumb Joystick is a Grove compatible module which is very similar to the 'analog' joystick on PS2 (PlayStation 2) controllers. Two direction movements will output different analog signals as they are actually two potentiometers. The resistor is ~10k for each.

    € 7,00
    In Stock
  • € 3,50 In Stock

    It is consist one coin type motor which is a Permanent Magnet coreless DC motor. It vibrates when the input is logic HIGH. It is very easy to drive and Grove compatible. Can be used in toys and cell phone modules.

    € 3,50
    In Stock
  • € 6,00 In Stock

    The Universal 4 Pin Buckled Cable is made for the Grove System to connect all of the Twigs to the Stem - Basic Shield or to other Twig compatible boards for quick prototyping. 

    € 6,00
    In Stock
  • € 5,50 In Stock

    This module is an incremental rotary encoder. It encodes the rotation signal from the axis and output the signal by electronic pulse. The Grove – Encoder is one of the Grove series and has a standard Grove interface.  When you need to add a rotary knob to your project, for example a volume knob for a speaker, a selection panel or a digital input, this...

    € 5,50
    In Stock
  • € 5,00 In Stock

    Some customer complain that can not use Arduino to control Grove modules directly. So we make this Grove to 4 Pin 2.54 female jumper wire. With this wire, you can easily connect all of Seeed Grove modules to any 2.54mm pitch connectors. 5 PCs is included in one pack.Length of each wire is 20cm. Note: Grove side uses buckled connector.

    € 5,00
    In Stock
Showing 1 - 16 of 25 items