Motor Driver / Controller There are 10 products.

Showing 1 - 10 of 10 items
  • € 35,00 In Stock

    The 4A Motor Shield is based on the Freescale MC33932 dual H-Bridge Power IC , which can control inductive loads with currents up to 5.0A peak per single bridge. It lets you drive two DC motors with your Arduino/Seeeduino board, controlling the speed and direction of each one independently. You can also measure the motor current absorption of each motor,...

    € 35,00
    In Stock
  • € 27,50 In Stock

    This carrier board for ST’s VNH5019 motor driver IC operates from 5.5 to 24 V and can deliver a continuous 12 A (30 A peak).

    € 27,50
    In Stock
  • € 5,00 In Stock

    The LN298 is a high voltage, high current, dual full-bridge motor driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors.

    € 5,00
    In Stock
  • € 35,00 In Stock
    Sale!

    The RedBot Mainboard is a robotic development platform that works with the Arduino IDE. The RedBot is a motor driver and Ardiuno combination with various headers and connections, eliminating the need to stack multiple shields. By using the RedBot accessory boards and your own chassis, you can design a robot to suit your needs.

    € 35,00
    In Stock
  • € 6,50 In Stock

    This compact breakout board makes it easy to use Allegro’s A4990 dual motor driver, which can control two bidirectional DC motors over a wide operating voltage range of 6 V to 32 V. It is capable of delivering a continuous 0.7 A to each motor channel, and onboard sense resistors enable the A4990 to limit the peak motor current to about 0.9 A per channel....

    € 6,50
    In Stock
  • € 8,50 In Stock

    Crank up your robotics with powerful Adafruit DRV8871 motor driver breakout board. This motor driver has a lot of great specs that make it useful for a wide variety of mechatronics. In particular, the simple resistor-set current limiting and auto-magic PWM support make it super easy to use with just about any brushed DC motor.

    € 8,50
    In Stock
  • € 6,50 In Stock

    Spin two DC motors or step one bi-polar or uni-polar stepper with up to 1.2A per channel using the DRV8833. This motor driver chip is a nice alternative to the TB6612 driver. Like that chip, you get 2 full H-bridges, but this chip is better for low voltage uses (can run from 2.7V up to 10.8V motor power) and has built in current limiting capability. We...

    € 6,50
    In Stock
  • € 42,50 In Stock

    The Pololu Simple Motor Controller 18v7 makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 30 V and is efficient enough to...

    € 42,50
    In Stock
  • € 72,50 In Stock

    The Pololu Simple High-Power Motor Controller makes basic control of brushed DC motors easy, with our free Simple Motor Control Center software enabling quick configuration over USB. The controller supports four interface modes: USB, TTL serial, analog voltage, and hobby radio control (RC). This version operates from 5.5 to 40 V and is efficient enough to...

    € 72,50
    In Stock
  • € 5,25 In Stock

    The L293DNE is a PTH quadruple, high-current, half-H driver IC. These ICs have been designed to provide bidirectional drive currents of up to 600mA at voltages from 4.5V to 36V. The L293DNE can drive inductive loads such as relays, solenoids, DC and bipolar stepping motors, as well as other high-current/high-voltage loads in positive supply applications.

    € 5,25
    In Stock
Showing 1 - 10 of 10 items